Polyaspartic polyurea floor coating
UV-resistant floor coating for concrete or epoxy-primed surfaces. The stated abrasion-resistance comparison with conventional epoxy flooring requires verification under matching test conditions.
- Product name:
- Polyaspartic polyurea floor coating
- Product category:
- flooring Paints
Product poster showing a green factory floor and floor-coating applications
Key features
- solids content ：≥95%
- Abrasion and compression resistance
- Seamless finish
Specifications
Technical documents and conditions of use
See the technical documents below for specification sources and conditions. Verify the exact grade and document version before application. Specification sources
This document covers the relevant product series. Confirm the exact model, substrate preparation, mixing ratio, dry film thickness, temperature, humidity, curing and test conditions. Typical series values are not guaranteed values for every application.
Verify performance and service-life statements against the relevant reports, specimen preparation, test standards and service conditions. Service-life figures without supporting reports are not durability guarantees; site photographs do not replace film-thickness testing or project acceptance records.
Website parameters follow the technical-parameters table on page 2 of the floor-coating TDS: surface-dry ≤3 h, through-dry ≤24 h, bond strength ≥2.6 MPa and elongation at break ≥300%. The recommended application rate is 500–1000 g/m² from the application data on page 2. Personnel access follows the precautions on page 3: keep personnel out for the first 12 hours after application. Floor Coating TDS, pages 2–3
| Parameter | Value / unit / conditions |
|---|---|
| Density | 1.2-1.3 g/cm³ |
| Touch-dry Time | ≤3 h |
| Through-dry time | ≤24 h |
| Full cure | 7 days (to final strength) |
| Tear strength | ≥60 N/mm |
| Bond strength | ≥2.6 MPa |
| Temperature resistance | -40℃~130℃ |
| Water absorption | ＜0.3% |
| Salt-spray resistance | ≥3000 h |
| VOC content | ≤30g/L |
| Hazardous substances | Refer to the grade-specific SDS and hazardous-substance test report. |
| Solids content | ≥95% |
| Tensile strength | 15-30 MPa |
| Elongation at break | ≥300% |
| Weather resistance | Confirm the applicable weathering test method, exposure duration and results. |
| Recommended application rate | 500–1000 g/m² |
| Personnel access | Keep personnel out for the first 12 hours after application |
Features
- Select the finish according to indoor or outdoor exposure.—Confirm weathering, cleaning and protective-layer requirements for the selected grade and finish.
- Review the grade-specific SDS, emissions data and ventilation requirements. Wear appropriate protective equipment; special contact uses require specific evidence.
- Evaluate abrasion, impact, rolling loads and chemical exposure using test conditions representative of the project. Compare different coatings only under consistent test methods.
- Apply by roller, spray or brush. Rapid curing permits foot traffic after the specified through-cure stage. Strong adhesion to concrete and compatible epoxy primers supports both new floors and refurbishment, with a smooth, uniform finish available in a range of colors.
Applications
Suitable for application to concrete substrates or compatible epoxy primers in factories, workshops, warehouses, car parks, shops, hospitals, schools, offices, residential living areas and balconies, food-processing facilities and pharmaceutical plants. It can be used as a new floor finish or refurbishment topcoat, especially where frequent use, contamination, abrasion, staining and environmental requirements are important.
Storage
This product is flammable and shall be stored in a low temperature seal, at a temperature consistent with ≤35℃, which requires that it be kept away from sources of fire, heat sources, strictly forbidden to tan, stored in a cold, dry and ventilated environment, in isolation from oxidizers, acids, for a storage period of 12 for a period of up to six months, after which it shall be used within an hour of 72, and the unused portion shall be sealed in such a way as to prevent tidal deterioration.
Key notes
These parameters represent typical performance ranges. Follow the product TDS/SDS, batch test report and actual service conditions. Contact us for the relevant documents, samples and application recommendations.
View more products
Our polyaspartic product range serves a variety of industries.
Return to Product Center